Outdoor
How Many Fence Posts and Pickets Do You Need for 100 Feet?
Quick answer: A 100 ft picket fence with posts every 8 ft needs 14 posts, 220 pickets and 26 rails, plus 28 bags of 80 lb concrete if you set each post in 2 bags. The picket count is based on 5.5 inch pickets with a half inch gap and includes 10 percent waste. Adding a gate changes the numbers slightly, as shown below.
A fence looks simple, but the shopping list has several parts that depend on each other: posts, rails, pickets, concrete and hardware. Get the posts right and the rest follows. The figures below come from the fence calculator.
- Posts14 posts
- Pickets220 pickets
- Rails26 rails
- Concrete mix for post holes, 80 lb bags28 bags
Fence materials for 100 feet at a glance
For a 100 ft run with the calculator's defaults, the shopping list is:
| Item | Quantity | How it is worked out |
|---|---|---|
| Posts | 14 | 13 sections plus 1 |
| Pickets | 220 | 200 pickets plus 10% waste |
| Rails | 26 | 13 sections × 2 rails |
| 80 lb concrete bags | 28 | 14 posts × 2 bags |
These are for a straight fence. If your fence has corners, gates or changes in grade, the numbers change, and you should add posts for each corner and gate.
How to calculate fence posts
Posts go at both ends of each section, and the end of one section is the start of the next. That means the number of posts is always one more than the number of sections.
- Divide the length by the post spacing. With posts 8 ft apart: 100 ÷ 8 = 12.5.
- Round up to whole sections. That gives 13 sections. You round up because a partial section still needs a post at its end.
- Add one. 13 + 1 = 14 posts.
The most common mistake is forgetting the extra post. A fence with 13 sections has 14 posts, not 13. The post spacing is a design choice. Eight feet is common, and it matches the length of many rails and fence panels, but your local practice, your materials and any rules from your town may call for something else.
How spacing changes the post count
Closer posts make a stronger fence but cost more in posts, rails and concrete. Wider spacing saves posts but needs sturdier rails.
| Post spacing | Posts for 100 ft | Rails | Concrete bags |
|---|---|---|---|
| 6 ft | 18 | 34 | 36 |
| 8 ft | 14 | 26 | 28 |
| 10 ft | 11 | 20 | 22 |
Moving from 6 ft spacing to 10 ft spacing cuts the posts from 18 to 11. The number of pickets does not change, because pickets cover the whole length of the fence regardless of the posts.
How to calculate pickets
Pickets are the boards that form the face of the fence. The number you need depends on the width of one picket and the gap between pickets.
- Find the pitch. Each picket takes up its own width plus one gap. With 5.5 inch pickets and a 0.5 inch gap, the pitch is 6 inches, so 12 ÷ 6 = 2 pickets per foot.
- Multiply by the length. 100 ft × 2 = 200 pickets.
- Add waste. Ten percent covers cuts, splits and mistakes: 200 × 1.10 = 220 pickets.
If you want a different look, change the picket width or the gap. A smaller gap needs more pickets. Solid privacy fences use no gap, which is a different design and needs a different count. Without any waste allowance the same fence needs 200 pickets. The extra 20 pickets are a sensible buffer, and the waste factor guide explains how to choose the percentage.
How many rails do you need?
Rails run horizontally between posts and hold the pickets. The number of rails per section depends on the fence height and style.
| Rails per section | Rails for 100 ft |
|---|---|
| 2 rails | 26 |
| 3 rails | 39 |
| 4 rails | 52 |
A shorter fence of about 4 ft often uses 2 rails per section. Taller fences need a middle rail so pickets do not bow, and the calculator offers 3 or 4 rails for them. The right choice depends on your design and your materials. Check the manufacturer's instructions or ask your supplier.
What happens when you add a gate
A gate opening is not covered by pickets, so the calculator takes the width of the gate out of the fenced run and then adds the gate posts. Because the shorter run needs fewer sections, the post total moves very little: it stays at 14 for one 4 ft gate and rises to 15 for two in this example. The pickets and rails drop because there is less fence to cover.
With one 4 ft gate the numbers change like this:
| Item | No gate | One 4 ft gate | Two 4 ft gates |
|---|---|---|---|
| Posts | 14 | 14 | 15 |
| Pickets | 220 | 212 | 203 |
| Rails | 26 | 24 | 24 |
The gate hardware (hinges, latch and a frame or brace) is a separate item. Gates are often wider and need heavier posts than the rest of the fence, because the gate puts a load on one side. Read the gate hardware instructions for the post size and the spacing.
How much concrete do fence posts need?
Setting posts in concrete is common, and the amount depends on the hole size and depth. A common rule of thumb is about 2 bags of 80 lb concrete per post, which gives 28 bags for 14 posts. That number is a starting point, not a rule. A deeper or wider hole needs more, and some soil conditions allow you to use less. A traditional rule is to bury about a third of the post length, and local frost depth may require more. Ask your local building office about depth and any permit requirements.
If you want to check the exact volume of concrete for a hole, use the concrete columns and footings calculator, which works from the hole diameter and depth.
Common fence mistakes
- Counting posts as equal to sections. Add one post.
- Skipping the property line check. A fence is easy to put on the wrong side of a boundary. Confirm the line before you dig.
- Not calling before you dig. Underground utilities are dangerous and expensive to hit. In the United States, call 811 or use the request form on call811.com a few working days before you dig, because the rules and wait times vary by state.
- Ignoring permits and height limits. Many towns have rules for fence height, material and setback. Check them first.
- Buying the exact number of pickets. Splits, knots and mistakes eat into the count. Order the waste allowance.
- Forgetting slope. On a slope the fence length along the ground is longer than the horizontal run. Measure along the line of the fence.
- Ordering gates last. Gate posts and hardware change your layout. Plan them first.
Frequently asked questions
How many fence posts do I need for 100 feet?
With posts 8 ft apart you need 14 posts. That is 13 sections plus one for the end. At 6 ft spacing you need 18 posts, and at 10 ft you need 11.
How many pickets do I need for 100 feet of fence?
You need 220 pickets for 5.5 inch pickets with a half inch gap and 10 percent waste. Without the waste allowance you need 200.
How many fence rails do I need for 100 feet?
With 2 rails per section and 13 sections you need 26 rails. With 3 rails per section you need 39.
How many bags of concrete per fence post?
A common rule of thumb is 2 bags of 80 lb concrete per post, but the real number depends on the hole size and depth.
How far apart should fence posts be?
Eight feet is common for many wood fences. The best spacing depends on your materials, your design and local rules. Always follow the manufacturer's instructions for your rails or panels.
How do I calculate a fence with corners?
Add a post at each corner, and calculate each straight run separately. The posts at the corners are shared by two runs, so subtract one post for each corner when you add the runs together.
Do I subtract the gate opening?
Yes. The gate opening is not covered by pickets, and the calculator subtracts it from the fenced length. You also add posts for the gate.

Sources and assumptions
These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them in the calculator to match your product and your site.
| Setting | Value | Status | Source |
|---|---|---|---|
| fence post spacing | 8 ft | Editable default | contractor rule of thumb, editable |
| fence rails per section | 2 rails/section | Editable default | contractor rule of thumb, editable |
| fence post concrete bags | 2 bag/post | Editable default | Rule of thumb for 80 lb concrete bags set per fence post hole; depends on hole size. Not verified. |
Keep reading
- How Much Waste Factor Should You Add to Building Materials?Most projects need 5 to 15 percent extra material. See the waste factor for flooring, tile, drywall, paint…
- How to Measure a Room for Flooring, Paint and TrimLearn how to measure a room for flooring, paint, drywall and baseboard. Get floor area, wall area and…
- How Much Gravel Do You Need for a Patio Base?A 10x10 patio with a 4 inch gravel base needs 1.23 cubic yards, about 74 bags. See the formula, a depth…
- How Many Fence Posts and Pickets Do You Need for 25 Feet?A 25 ft picket fence with 8 ft post spacing needs 5 posts, 55 pickets and 8 rails. See spacing, rails and…
- How Many Fence Posts and Pickets Do You Need for 40 Feet?A 40 ft picket fence with 8 ft post spacing needs 6 posts, 88 pickets and 10 rails. See spacing, rails and…
- How Many Fence Posts and Pickets Do You Need for 50 Feet?A 50 ft picket fence with 8 ft post spacing needs 8 posts, 110 pickets and 14 rails. See spacing, rails and…
- How Many Fence Posts and Pickets Do You Need for 60 Feet?A 60 ft picket fence with 8 ft post spacing needs 9 posts, 132 pickets and 16 rails. See spacing, rails and…
- How Many Fence Posts and Pickets Do You Need for 75 Feet?A 75 ft picket fence with 8 ft post spacing needs 11 posts, 165 pickets and 20 rails. See spacing, rails and…
- How Many Fence Posts and Pickets Do You Need for 80 Feet?An 80 ft picket fence with 8 ft post spacing needs 11 posts, 176 pickets and 20 rails. See spacing, rails…