Outdoor
How Much Gravel Do You Need for a Patio Base?
Quick answer: A 10 ft × 10 ft patio with a 4 inch gravel base needs about 1.23 cubic yards of gravel. With 10 percent extra for compaction and uneven ground that becomes 1.36 cubic yards, which a supplier will usually sell as 1.5 cubic yards in bulk or you can buy as 74 bags of about 0.5 cubic feet each. The gravel weighs roughly 1.9 tons.
Gravel is the invisible layer under patios, walkways, sheds and slabs, and it is also the material that people most often order by guesswork. It is sold by volume, by weight and by the bag, and the three are easy to mix up. The figures below come from the gravel and mulch calculator.
- Gravel, bulk1.5 yd³
Gravel needed by depth for a 10x10 area
Depth is the number that changes the answer most. The table shows a 10 ft × 10 ft area at four depths, with 10 percent waste added.
| Depth | Cubic yards (no waste) | Bulk order (cubic yards) | Bags |
|---|---|---|---|
| 2 in | 0.62 | 1 | 37 |
| 3 in | 0.93 | 1.5 | 55 |
| 4 in | 1.23 | 1.5 | 74 |
| 6 in | 1.85 | 2.5 | 110 |
Doubling the depth doubles the gravel. Most patio bases are about 4 inches thick when compacted, but pavers, walkways and driveways often differ. Your paver or slab manufacturer will give a recommended base depth, and local practice and soil conditions matter. Soft or wet soil often needs a deeper base.
The gravel formula, step by step
Gravel is a volume calculation, and odd shapes are measured by splitting them into rectangles, as in how to measure a room for materials. You find the volume of a flat box that is the size of your area and the depth of your base, then convert the units.
- Find the area. Length × width = 10 × 10 = 100 square feet.
- Turn the depth into feet. 4 inches ÷ 12 = 0.333 ft.
- Find the volume. Area × depth = 100 × 0.333 = 33.33 cubic feet.
- Convert to cubic yards. One cubic yard is 27 cubic feet, so 33.33 ÷ 27 = 1.235 cubic yards.
- Add waste. Gravel compacts when it is tamped, and the ground is never perfectly flat. Ten percent extra gives 36.67 cubic feet, or 1.36 cubic yards.
- Round to the way it is sold. Bulk gravel is often sold in half-yard or full-yard steps. The calculator uses 0.5 cubic yard steps, which makes the order 1.5 cubic yards. For bags, divide by the yield per bag (0.5 cubic feet): 36.67 ÷ 0.5 = 73.3, which rounds up to 74 bags.
Bulk or bags: which is better?
The calculator treats about 1 cubic yard as the point where bulk delivery is usually more practical than bags. Your 10 × 10 base is 1.36 cubic yards with waste, so it is above that line.
Bags are convenient for small jobs. You can load a few into a car, move them by hand and use only what you need. For 74 bags, though, you would be lifting and moving a large amount of material. Bulk gravel comes by the truckload and is dumped in one pile, which you spread with a wheelbarrow and a rake. Delivery usually has a minimum order and a delivery fee, so ask the supplier. A good rule is to ask for a bulk quote whenever your total is more than about one cubic yard.
How much does the gravel weigh?
Weight matters when you are loading a truck or trailer. A cubic yard of crushed gravel weighs about 1.4 tons on average, although the real figure depends on the stone and how wet it is. For the 1.36 cubic yards in this example, that is about 1.9 tons. Many pickup trucks can carry only about a ton or less, so a small delivery is often safer and easier than hauling it yourself. Check your vehicle's payload before you load it, and ask the supplier for the actual weight if you pay by the ton.
Gravel, mulch, sand and soil: the same math
The same formula works for other loose materials. Only the depth and the typical order sizes change. The table shows a 10 ft × 10 ft area with common depths for each material:
| Material | Depth | Cubic yards (no waste) | Bulk order |
|---|---|---|---|
| Gravel | 4 in | 1.23 | 1.5 yd³ |
| Sand | 1 in | 0.31 | 0.5 yd³ |
| Mulch | 3 in | 0.93 | 1.5 yd³ |
| Topsoil | 4 in | 1.23 | 1.5 yd³ |
Mulch is usually spread 2 to 3 inches deep, the sand bedding under pavers about 1 inch, and topsoil 4 inches or more for a lawn. Always check the recommended depth for your project and product.
Area examples
| Area | Cubic yards at 4 in | Bulk order (cubic yards) | Bags |
|---|---|---|---|
| 8 x 8 ft | 0.79 | 1 | 47 |
| 10 x 10 ft | 1.23 | 1.5 | 74 |
| 10 x 12 ft | 1.48 | 2 | 88 |
| 12 x 16 ft | 2.37 | 3 | 141 |
| 20 x 20 ft | 4.94 | 5.5 | 294 |
The bag count grows quickly with size, which is why larger projects almost always use bulk gravel.
What kind of gravel for a patio base?
The calculator does not choose the stone for you, but the type matters. Base layers under pavers and slabs commonly use crushed stone with a mix of sizes, sometimes sold as a "base" or "road base", because it packs tightly and drains well. Rounded pea gravel is pretty but does not lock together, so it is usually used on top rather than under a rigid surface. Ask your supplier which product they recommend for your use.
Preparing the base
- Mark the area and dig out the topsoil. Remove grass and soft soil, and dig deep enough for the base and the surface that goes on top.
- Grade it. Slope the ground slightly away from buildings so water drains.
- Add the gravel in layers. Spread it in lifts of a few inches and compact each lift with a plate compactor or a hand tamper.
- Check levels. Use a straightedge and level to confirm the base is flat and at the right height.
- Add a bedding layer if your surface needs one. Pavers often sit on a thin layer of sand over the gravel.
If you are pouring a slab on the gravel, use the concrete slab guide to work out the concrete, and plan the base and the slab together.
Common mistakes
- Mixing up cubic yards and tons. Gravel can be sold by either. Make sure you and the supplier are using the same unit.
- Not allowing for compaction. Loose gravel settles when you tamp it. The waste allowance is there for this.
- Making the base too thin. A thin base can settle and crack the surface above it.
- Using the wrong stone. Round stone slides under load. Angular, crushed stone locks together.
- Ordering by guess. A little arithmetic saves a second delivery fee.
- Skipping drainage. Water under a patio can heave it in winter or soften the soil. Grade for drainage.
Frequently asked questions
How many cubic yards of gravel do I need for a 10x10 patio?
A 4 inch base over 10 × 10 feet needs 1.23 cubic yards, or 1.36 cubic yards with 10 percent for compaction. A bulk order is usually 1.5 cubic yards.
How many bags of gravel for a 10x10 area?
With bags of 0.5 cubic feet each you need 74 bags for a 4 inch base. At 2 inches you need 37.
How much gravel do I need for a 12x16 area?
A 12 × 16 area with a 4 inch base needs 2.37 cubic yards before waste. The bulk order is 3 cubic yards.
How many tons is a cubic yard of gravel?
About 1.4 tons for typical crushed gravel, though it varies with the stone and moisture.
How deep should a gravel base be?
For many patios and walkways, about 4 inches of compacted gravel is common. Driveways, wet soil and heavy loads need more. Follow your paver or slab maker's instructions and local practice.
Do I need to compact gravel?
Yes. Compacting makes the base firm and stops it from settling later. Do it in layers.
Should I order extra gravel?
Yes. Ten percent is a common allowance. It is usually easier than arranging a second delivery.

Sources and assumptions
These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them in the calculator to match your product and your site.
| Setting | Value | Status | Source |
|---|---|---|---|
| gravel mulch waste | 10 % | Editable default | contractor rule of thumb, editable |
| gravel mulch bag yield | 0.5 ft3/bag | Editable default | manufacturer label typical |
| mulch bag yield | 2 ft3/bag | Verified 2026-11-15 | Scotts Nature Scapes Color Enhanced Mulch is sold in 2 cu ft bags; the listing gives 12 sq ft of coverage at 2 in deep. 1.5 and 3 cu ft bags also exist, so check the bag. |
| bulk order increment | 0.5 yd3 | Editable default | Assumed ordering step for bulk gravel, mulch, soil and sand; yards differ. Rule of thumb, not verified. |
| gravel density | 1.4 ton/yd3 | Editable default | Typical loose crushed gravel weight, about 1.4 tons per cubic yard; varies by stone and moisture. Not verified. |
| gravel bulk threshold | 1 yd3 | Editable default | Above about 1 cubic yard, bulk delivery is usually cheaper and quicker than bags. Rule of thumb, not verified. |
Keep reading
- How Many Bags of Concrete Do You Need for a 10x10 Slab?A 4-inch 10x10 slab needs 62 bags of 80 lb concrete with waste. See 60 lb and 40 lb counts, a thickness…
- How Many Deck Boards Do You Need for a 12x16 Deck?A 12x16 deck with 5.5 inch boards needs 29 boards (16 ft long) and 13 joists at 16 inch spacing. See the…
- How Much Waste Factor Should You Add to Building Materials?Most projects need 5 to 15 percent extra material. See the waste factor for flooring, tile, drywall, paint…
- How Much Gravel Do You Need for a 6x6 Patio Base?A 6x6 ft patio base 4 inches deep needs 0.44 cubic yards of gravel, 0.5 yd³ in bulk or 27 bags. See depth…
- How Much Gravel Do You Need for an 8x8 Patio Base?An 8x8 ft patio base 4 inches deep needs 0.79 cubic yards of gravel, 1 yd³ in bulk or 47 bags. See depth…
- How Much Gravel Do You Need for an 8x10 Patio Base?An 8x10 ft patio base 4 inches deep needs 0.99 cubic yards of gravel, 1.5 yd³ in bulk or 59 bags. See depth…
- How Much Gravel Do You Need for a 10x12 Patio Base?A 10x12 ft patio base 4 inches deep needs 1.48 cubic yards of gravel, 2 yd³ in bulk or 88 bags. See depth…
- How Much Gravel Do You Need for a 10x15 Patio Base?A 10x15 ft patio base 4 inches deep needs 1.85 cubic yards of gravel, 2.5 yd³ in bulk or 110 bags. See depth…
- How Much Gravel Do You Need for a 12x12 Patio Base?A 12x12 ft patio base 4 inches deep needs 1.78 cubic yards of gravel, 2 yd³ in bulk or 106 bags. See depth…