Insulation calculator

Batts, blown-in or spray foam for walls, attics or floors: packages, bags or kits for an area.

Open the interactive calculator

Insulation needed by size

SizeMain resultShopping list
8 × 8 ft2 packages2 packages Insulation R-13, 40 ft² per package
10 × 10 ft3 packages3 packages Insulation R-13, 40 ft² per package
10 × 12 ft4 packages4 packages Insulation R-13, 40 ft² per package
12 × 12 ft4 packages4 packages Insulation R-13, 40 ft² per package
12 × 16 ft6 packages6 packages Insulation R-13, 40 ft² per package
16 × 20 ft9 packages9 packages Insulation R-13, 40 ft² per package
20 × 20 ft11 packages11 packages Insulation R-13, 40 ft² per package
24 × 24 ft16 packages16 packages Insulation R-13, 40 ft² per package

Every other setting is at the calculator's default. Change them in the calculator for your own job.

Worked example

Using the default sizes, the result is 5 packages (160 ft²).

ItemQuantityNote
Insulation R-13, 40 ft² per package5 packageincludes 5% waste

How it is calculated

  1. Area: length x width
    20 x 8 = 160 ft²
  2. With waste: area x (1 + waste)
    160.0 x 1.05 = 168 ft²
  3. Packages: area with waste ÷ coverage, rounded up
    168.0 ÷ 40 = 4.2 packages

What to enter

FieldUnitHelp
Type of insulationchooseBatts and rolls are counted by package, blown-in by bag from the R-value chart, spray foam by kit.
Area lengthftLength of the wall, ceiling or floor area.
Area width or heightftThe other side of the area.
R-value you plan to usechooseThe right R-value depends on your climate and local code. For blown-in, R-30, R-38 and R-49 set the bag coverage from the chart.
Doors and windows (optional)ft²Area of openings to leave out. 0 if none.
Coverage per packageft²Square feet covered by one bag or roll, from the label. Blown-in at R-30, R-38 or R-49 uses the chart instead.
Spray foam thicknessinOnly for spray foam. Kits are rated in board feet: 1 ft² at 1 in thick.
Extra for waste%Cuts around framing, wiring and openings.

Frequently asked questions

How do I calculate insulation?

Batts, blown-in or spray foam for walls, attics or floors: packages, bags or kits for an area. Enter your sizes in the calculator. It works out area (length x width) and the later steps, then rounds up to what stores sell.

How much waste should I add?

The calculator starts at 5%. Source: Contractor rule of thumb for batt insulation. Not verified. You can change it. More cuts, patterns or uneven ground need more.

Where does the insulation waste number come from?

5 percent. Contractor rule of thumb for batt insulation. Not verified. This is an editable starting value, not an official figure. Change it if your product label or supplier says otherwise.

Where does the insulation package coverage number come from?

40 ft2/package. Typical batt package coverage; varies by product. Check the label. Not verified. This is an editable starting value, not an official figure. Change it if your product label or supplier says otherwise.

Where does the blown coverage r30 number come from?

68.5 ft2/bag. Owens Corning AttiCat blown-in fiberglass fact sheet: R-30 at 14.6 bags per 1,000 sq ft, 68.5 sq ft per bag, 10.75 in minimum thickness. Other products and bag weights differ; the bag label is the authority. Checked against its source on 2026-11-15.

Where does the blown coverage r38 number come from?

52.6 ft2/bag. Owens Corning AttiCat chart as quoted by third-party calculators: R-38 at about 52.6 sq ft per bag (19 bags per 1,000 sq ft). Not verified against the maker sheet; check the bag label. This is an editable starting value, not an official figure. Change it if your product label or supplier says otherwise.

Where does the blown coverage r49 number come from?

39.9 ft2/bag. Owens Corning AttiCat chart as quoted by third-party calculators: R-49 at about 39.9 sq ft per bag (25 bags per 1,000 sq ft). Not verified against the maker sheet; check the bag label. This is an editable starting value, not an official figure. Change it if your product label or supplier says otherwise.

Where does the foam kit board feet number come from?

600 board ft/kit. Two-part spray foam kits are rated in board feet (1 sq ft at 1 in thick); a 600 kit such as Froth-Pak 600 covers about 600 sq ft at 1 in. Yield drops in cold conditions. Not verified against the maker sheet. This is an editable starting value, not an official figure. Change it if your product label or supplier says otherwise.

Does this calculator show prices?

No. It gives quantities and a shopping list you can share, print or export. Ask your supplier for prices.

Related calculators