EnoughToBuy Guides

Outdoor

How Many Retaining Wall Blocks Do You Need for a Fire Pit?

By the EnoughToBuy teamUpdated November 15, 20265 min readSources and assumptions

Quick answer: A round fire pit that measures 46 inches across the outside, built 3 courses high with blocks 12 inches wide and 6 inches tall, takes 13 blocks per course, 39 for the ring, and 43 blocks with 10 percent spare for breakage and fit. A cap ring on top adds about 15 caps. Measure the outside of the ring, not the fire bowl inside.

A fire pit ring is a short retaining wall bent into a circle, so the retaining wall calculator can count it: the length of the wall is the distance around the outside of the ring. Wall blocks with a tapered back fit a circle without cutting, with the wide front face on the outside. The mini calculator above is set to a 46 inch ring, 12.04 feet around. For straight walls, read how many retaining wall blocks do I need.

Try itRetaining wall blocks: enter your own sizes
You would buy43blocks
  • Wall blocks (12 x 6 in face)43 blocks
  • Cap blocks15 caps
  • Gravel, bulk (backfill)0 yd³
Open the full calculator with more options

The fire pit block formula

  1. Distance around. 3.14 × outside diameter. For 46 inches: 3.14 × 46 ÷ 12 = 12.04 feet.
  2. Blocks per course. 12.04 feet ÷ the 12 inch block face, rounded up = 13 blocks.
  3. Courses. 18 inches of wall ÷ 6 inch blocks = 3 courses.
  4. Spares. 13 × 3 = 39, plus 10 percent = 43 blocks.

Rounding up each course means the last block in the ring can be a little tight or need a bigger gap. Tapered blocks have some play, so most rings close without cutting.

1.5 ft visible capsoil 3 courses of 6 in (0 buried), 13 blocks per course on 12.04 ft
The ring of a 46 in fire pit unrolled into a straight wall 12.04 ft long: the calculator counts blocks along it course by course.

Blocks by fire pit size

Outside diameterDistance around, ftBlocks per courseBlocks, 3 courses with sparesCaps
36 in9.42103311
40 in10.47113713
44 in11.52124014
46 in12.04134315
48 in12.57134315
54 in14.14155017
60 in15.71165318

Pre-packaged fire pit kits are sold by their outside size, which is why this chart uses it. The opening inside is smaller by twice the depth of the block, front to back. If you start from the inside opening you want, add twice your block's depth to get the outside diameter, then read the row.

Blocks by height

Height of a 46 in ringBlocks, no sparesBlocks with spares
2 courses (12 in)2629
3 courses (18 in)3943
4 courses (24 in)5258

Fire pits are usually knee to seat height. Two courses of these blocks make a low ring for a portable fire bowl, three or four make a seat-height wall to rest your feet on.

Blocks by block size

Block faces differ by product line. The count follows the face width:

Block face widthBlocks per course, 46 in ringBlocks, 3 courses with spares
8 in1963
10.5 in1447
12 in1343
16 in1033

Check the label for the face width and height of the block you buy, and enter both in the calculator.

Building the ring

  • Base. Dig a shallow circle, add compacted gravel, and level it carefully. The first course decides how true the whole ring sits.
  • Layout. Mark the outside circle with a stake and string set to half the outside diameter, 23 inches for this ring, and set the first course to the line.
  • Stagger. Offset each course by half a block so the joints do not line up, and glue the upper courses and the caps with masonry adhesive if the maker calls for it.
  • Heat. Ordinary concrete wall blocks can crack or spall in direct flame. Many builders line the inside with a steel fire ring or fire brick, so check what the block maker allows.
  • Clearances. Local rules set how far a fire pit must sit from the house, fences and trees, and some areas ban open fires. Check before you build.

Square fire pits and other shapes

A square fire pit is four short straight walls, so measure the outside of each side and add them up for the wall length, or run the calculator once per side. Straight-sided blocks suit a square better than tapered ones, and the corners need either corner blocks or a cut on every other course so the joints stagger. An oval or a ring with a seat wall attached is easiest to count in parts: the curved part with the method above, the straight parts as ordinary walls.

What else to buy for a fire pit

  • Base gravel for the leveling pad under the first course, and a hand tamper or plate compactor. How much gravel for a patio base shows how to work out the volume.
  • Masonry adhesive for the upper courses and the caps, in a grade the block maker approves.
  • A steel fire ring sized to the inside opening, or fire brick to line it.
  • Drainage in the bottom of the pit: a layer of gravel lets rain soak away instead of standing in the ring.
  • A patio around it, if you want one: how many pavers do I need counts pavers, base and sand for the surface.
  • A spark screen and a poker, and a hose or extinguisher within reach whenever the fire is lit.

Frequently asked questions

How many retaining wall blocks do I need for a fire pit?

For a 46 inch outside diameter and 3 courses of 12 inch blocks: 13 per course, 43 in all with spares, and about 15 caps.

How many blocks for a 36 inch fire pit?

If the ring is 36 inches across the outside, it takes 10 blocks per course and 33 for 3 courses with spares. If 36 inches is the inside opening, add twice the block depth to find the outside size and read that row of the chart.

How many blocks for a 60 inch fire pit?

16 blocks per course and 53 for 3 courses with spares, plus about 18 caps.

Do I need caps on a fire pit?

No, but caps give a flat top to sit on or set a drink on, and they cover the hollow cores of some blocks. A ring of caps is about one cap per block in the top course.

Can I use retaining wall blocks for a fire pit?

Many people do, but plain concrete blocks are not rated for direct flame. A steel fire ring or a lining of fire brick protects the inner face. Read the block maker's guidance.

How Many Retaining Wall Blocks Do You Need for a Fire Pit?
Save or share this answer.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them in the calculator to match your product and your site.

SettingValueStatusSource
retaining wall waste10 percentEditable defaultContractor rule of thumb. Not verified.

Keep reading