EnoughToBuy Guides

Paint & drywall

How Many Sheets of Drywall Do You Need for a Room?

By the EnoughToBuy teamUpdated November 13, 20266 min readSources and assumptions

Quick answer: A 12 ft × 10 ft room with 8 ft ceilings needs 17 sheets of 4×8 drywall to cover the walls and the ceiling, with a 10 percent allowance for waste. Covering only the walls takes 13 sheets. The ceiling alone takes 5. With 4×12 sheets, the same room needs 11.

Drywall is sold in sheets, so the job is a surface-area calculation followed by a division and a round up. The tricky parts are knowing what to include, how much to allow for cutting, and which sheet size is easier to handle. The figures below come from the drywall calculator.

Try itDrywall: enter your own sizes
You would buy17sheets
  • Drywall sheets, 4 × 8 ft17 sheets
  • Joint compound, ready-mixed1 pail
Open the full calculator with more options

How many sheets of drywall for common room sizes

This chart assumes 8 ft ceilings, no openings subtracted, and 10 percent waste. The first column shows the number of 4×8 sheets for walls and ceiling together. The other columns show alternatives.

Room size4x8 sheets, walls + ceiling4x12 sheets, walls + ceiling4x8, walls only4x8, ceiling only
10 x 10 ft1510114
12 x 10 ft1711135
12 x 12 ft1913145
14 x 12 ft2114156
16 x 14 ft2517178
20 x 16 ft31212011

If your room is somewhere in between, pick the next size up or enter your exact dimensions in the calculator. The numbers are rounded up to whole sheets because you cannot buy part of one.

12 ft 8 ft 10 ft deep
Walls plus ceiling make up the surface that sheets of drywall have to cover.

The drywall formula, step by step

Standard drywall panels are 4 ft wide, and the standard lengths are 8, 9, 10, 12, 14 and 16 ft according to the Gypsum Association's product standard (see GA-223). A 4×8 sheet covers 32 square feet and a 4×12 sheet covers 48 square feet. With that, the math for a 12 × 10 room is:

  1. Wall area. 2 × (length + width) × height = 2 × (12 + 10) × 8 = 352 square feet.
  2. Ceiling area. Length × width = 12 × 10 = 120 square feet.
  3. Total surface. 352 + 120 = 472 square feet.
  4. Add waste. Multiply by 1.10: 472 × 1.10 = 519.2 square feet.
  5. Divide by the sheet area. 519.2 ÷ 32 = 16.23 sheets.
  6. Round up. The result is 17 sheets.

You will notice that the exact figure, 16.23, is a little above 16, so the round-up adds almost a full sheet. That is normal. It also gives you offcuts you can use for small areas such as the strip above a door.

Should you buy 4x8 or 4x12 sheets?

The area math is the same for both, but the sheet size changes how many pieces you handle and how many joints you end up finishing. A 4×12 sheet covers 48 square feet, which is half again as much as a 4×8 sheet. In the example room that means 11 sheets instead of 17.

Longer sheets mean fewer seams, and fewer seams mean less taping and mudding. Many people choose 12 ft sheets for ceilings and long walls for that reason. The trade-offs are weight, which makes them harder to carry and lift alone, and access, because a 12 ft sheet is awkward to get through a tight stairwell or hallway. Check that you can carry the sheets into the room before you order them. Standard 4×8 sheets are the easiest to handle and are the default for most DIY jobs.

Walls only, ceiling only, or both?

The calculator lets you choose which surfaces to cover. The same room needs 13 sheets for walls only, 5 for the ceiling only, and 17 for both. The totals do not add up exactly (13 + 5 is more than 17) because each total is rounded up separately. When you cover both surfaces the offcuts from one can be used on the other.

Ceilings are usually hung first. A sheet on the ceiling is heavy and awkward, so many people rent a drywall lift for the job. Walls follow, and many installers hang long sheets horizontally on walls so the seams fall at a convenient height and are easier to finish.

Doors and windows: do you subtract them?

You can subtract openings to save a sheet or two, but be careful. Door and window openings are cut out of larger sheets, and the cut-out pieces are rarely reusable. Many installers do not subtract small openings at all. The calculator has an openings box so you can try both ways.

Openings taken off the walls4x8 sheets for walls and ceiling
0 ft²17
20 ft²16
40 ft²15
60 ft²15

Taking 40 square feet of openings off the walls, roughly one door and one window, changes the total from 17 sheets to 15. If the saving is small, leave the openings in and treat the spare sheet as insurance against mistakes.

How much waste should you allow?

The calculator starts at 10 percent, a common contractor rule of thumb. Cutting around corners, outlets, windows and doors creates offcuts, and a few sheets are always damaged in transport or while handling. The waste allowance covers all of it.

Waste allowanceSheets for walls and ceiling
5%16
10%17
15%17

Rooms with many openings, angled walls or complicated cuts need more. Large, simple rectangular rooms need less. Whatever you choose, remember that you will also pay for any sheet you do not use, so aim for a number you can justify.

What else goes on the shopping list

The sheets are only part of the order. A complete drywall job usually needs:

  • Drywall screws and a screw gun with a depth setting.
  • Paper or mesh joint tape.
  • Joint compound, sold in buckets or boxes, for taping and finishing coats.
  • Corner bead for outside corners.
  • Sanding supplies, a pole sander and a dust mask.
  • Primer, because bare joint compound and paper absorb paint unevenly.

Quantities for these depend on the product, so read the package labels. Joint compound coverage in particular varies by type.

Once the walls are finished and primed, the next job is color. The guide on how much paint you need for a room uses the same wall measurements, and how to measure a room for materials shows how to take them accurately, including L-shaped rooms.

Common drywall mistakes

  1. Forgetting the ceiling. If you plan to cover the ceiling too, include it in the area from the start.
  2. Using floor area only. Walls and ceilings are different surfaces, and each needs its own area.
  3. Not rounding up. Always round up to the next whole sheet.
  4. Ignoring thickness. Drywall comes in several thicknesses. Half-inch sheets are common on walls, and thicker sheets are often chosen for ceilings or where fire resistance is needed. Check your plans or your local code.
  5. Ordering too few for a complicated room. Every corner, soffit and angle needs extra material.
  6. Storing sheets badly. Drywall must stay dry and flat. Lean it against a wall for long and it can bend.

Frequently asked questions

How many sheets of drywall do I need for a 12x12 room?

A 12 × 12 room with 8 ft ceilings needs 19 sheets of 4×8 drywall for walls and ceiling, with 10 percent waste. Walls alone need 14 sheets.

How many 4x8 sheets of drywall for a 10x10 room?

A 10 × 10 room with 8 ft walls needs 15 sheets of 4×8 for walls and ceiling. Walls only needs 11.

How many sheets of drywall cover a ceiling?

A 12 × 10 ceiling needs 5 sheets of 4×8. The area is 120 square feet, and a sheet covers 32. With 10 percent waste you need about 4.13 sheets, which rounds up to 5.

How many square feet is a sheet of drywall?

A 4×8 sheet covers 32 square feet. A 4×12 sheet covers 48 square feet. Standard panels are 48 inches wide.

Is it better to hang drywall horizontally or vertically?

Many installers hang it horizontally on walls because it reduces the number of seams on a standard 8 ft wall, and seams are what take time to finish. Follow your local practice and the instructions that come with your drywall.

How much waste is normal for drywall?

Ten percent is a common allowance. Simple rooms can get by with less, and complicated rooms need more.

Do I need to subtract windows and doors?

You can, but the savings are small and the cut-outs are hard to reuse. Many installers leave openings in the count so they have spare material.

How Many Sheets of Drywall Do You Need for a Room?
Save or share this answer.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them in the calculator to match your product and your site.

Keep reading