EnoughToBuy Guides

Concrete & masonry

How Many Cinder Blocks Do You Need for a Wall?

By the EnoughToBuy teamUpdated November 17, 20266 min readSources and assumptions

Quick answer: A 20 ft long wall that is 4 ft high is 80 ft² of wall. A standard concrete block covers about 0.89 ft², so you need 90 blocks with no waste, or 95 blocks with 5% extra. That is 1.125 blocks per ft² of wall.

"Cinder block" is the everyday name for the hollow concrete block (CMU) sold at building supply stores. The count is simple area math, and this guide shows each step so you can run it for your own wall. The numbers come from the block and brick wall calculator, and the example is a 20 x 4 ft wall because that is what the calculator opens on.

Try itBlock or brick wall: enter your own sizes
You would buy95blocks
  • Concrete blocks, 16 x 8 in face95 blocks
Open the full calculator with more options

How many blocks per square foot

Block sizes are nominal. A block sold as 8 x 8 x 16 in is a little smaller than that, so that the mortar joint makes up the difference. When you add the joint back, each block takes up a 16 x 8 in face, or 128 in², of the wall.

A square foot is 144 in². Divide it by the face area and you get the block count per square foot:

  • 144 ÷ 128 = 1.125 blocks per ft².

That one figure is all you need. Multiply it by the wall area and you have the number of blocks, before waste.

20 ft 4 ft 16 x 8 in blocks, running bond
The 20 x 4 ft example wall drawn in 16 x 8 in blocks laid in running bond, each course offset half a block from the one below.

The math, step by step

Use your own length and height in place of the example.

  1. Find the wall area. Length times height, minus any openings: 20 ft × 4 ft − 0 = 80 ft².
  2. Multiply by the blocks per square foot. 80 ft² × 1.125 = 90 blocks.
  3. Add the waste allowance. 90 × 1.05 = 94.5.
  4. Round up to whole blocks. 95 blocks.

Blocks come as whole units, so always round up. A part of a block is of no use on the wall, and a shortage stops the job while you drive back to the store.

If your wall is not a rectangle, split it into rectangles, find each area and add them. The guide on how to measure a room for materials shows how to break a layout into simple shapes.

Block counts by wall size

Here are common wall sizes with the 5% waste allowance the calculator starts with. All of them are solid walls with no openings.

Wall sizeWall areaBlocks, no wasteBlocks, with waste
10 x 3 ft30 ft²3436
10 x 4 ft40 ft²4548
20 x 4 ft80 ft²9095
20 x 6 ft120 ft²135142
30 x 4 ft120 ft²135142
40 x 6 ft240 ft²270284

Doubling the length doubles the count, and so does doubling the height. The 20 x 4 ft wall is 90 blocks before waste. A 20 x 6 ft wall is the same length and half again as tall, and the table shows what that adds.

Subtracting doors and windows

Openings take blocks out of the count, so subtract their area from the wall area. The calculator has an openings field for this, in square feet.

Take a 24 ft long wall that is 8 ft high, with one 3 x 7 ft door and one 4 x 3 ft window:

  • Door area: 3 × 7 = 21 ft².
  • Window area: 4 × 3 = 12 ft².
  • Wall area with no openings: 24 × 8 = 192 ft².
CaseOpeningsWall areaBlocks, with waste
Solid wall0 ft²192 ft²227
With the door21 ft²171 ft²202
With the door and window33 ft²159 ft²188

The door and window together save 39 blocks. Treat that as the most you can save, not a sure saving. Blocks around an opening are cut or set in special shapes, and a lintel or other support above the opening is a separate item. Check local code for how openings in a block wall must be framed and supported.

How much waste to add

Blocks chip and crack in transport, and some get cut to fit at ends and corners. The calculator starts at 5%, a contractor rule of thumb and not an official figure. Here is how the percentage moves the count for the 20 x 4 ft wall:

Waste allowanceBlocks to buy
0%90
5%95
10%99
15%104

A straight wall with full-length courses and few cuts sits at the low end. A wall with many corners, openings or stepped ends sits higher. The guide on how much waste factor to add explains how to choose a margin for any material.

Concrete block or brick for the same wall

If you are choosing between block and brick for a low wall, the count per square foot is very different, because a brick face is much smaller.

UnitFace with jointUnits per ft²No wasteWith waste
Concrete block128 in²1.1259095
Modular brick21.3 in²6.75540567

Both rows are for the same 20 x 4 ft wall. The brick face comes from an editable default, because brick and joint sizes vary: check the size of the brick you buy.

What the count does not include

The calculator counts the blocks for the face of the wall and nothing else. It does not estimate:

  • Mortar, which you buy separately.
  • Rebar and grout for reinforced walls.
  • The footing under the wall, whose size and depth come from local code and soil.
  • Caps, lintels, flashing, ties and weep holes where they apply.

A wall that holds back soil or carries a load is structural. Check local code and ask a licensed professional before you design or build one. For a landscape wall of interlocking segmental blocks, use the retaining wall calculator instead, since those blocks are sized and counted differently.

Common mistakes when counting blocks

  1. Forgetting the mortar joint in the face size. The nominal 16 x 8 in face already includes it. Do not divide by the actual size of the block, or you will count too many.
  2. Using the wrong height. Measure the block wall itself, from the top of the footing to the top of the wall. The footing is a separate item.
  3. Not rounding up. A fraction of a block still means one more block to buy.
  4. Skipping the waste allowance. A count with no margin is short by the first cracked block.
  5. Subtracting openings but forgetting what they need. Lintels and cut blocks around the openings are extra.
  6. Treating the count as the whole job. Mortar, reinforcement and the footing are separate lists, and the footing depends on local code.
  7. Using a brick count for blocks. The units per square foot are far apart. Pick the right unit first.

Frequently asked questions

How many cinder blocks do I need for a 20 ft wall that is 4 ft high?

You need 90 blocks with no waste and 95 with 5% extra. The wall is 80 ft².

How many blocks are in a square foot of wall?

For a block with a 16 x 8 in face, 1.125. That is 144 ÷ 128. The face size includes the mortar joint.

Is a cinder block the same as a concrete block?

People use both names for the hollow block laid in walls. Stores usually sell it as a concrete block or CMU. Check the product label for the actual size and type.

How do I subtract a door or window?

Multiply its width by its height to get square feet and enter the total in the openings field. For the 24 x 8 ft example, one 3 x 7 ft door takes the count from 227 to 202 blocks with waste.

How many blocks do I need if I use bricks instead?

The same 20 x 4 ft wall takes 540 bricks with no waste and 567 with 5% extra, at 6.75 bricks per ft².

Does the count include mortar?

No. The calculator counts blocks only. Mortar, rebar, grout and the footing are separate. Read the label of the mortar you choose for its coverage.

How much waste should I add?

The calculator starts at 5%, which is a rule of thumb. Use more for a wall with many cuts, corners or openings.

How Many Cinder Blocks Do You Need for a Wall?
Save or share this answer.

Sources and assumptions

These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them in the calculator to match your product and your site.

Keep reading