Outdoor
How Much Sand and Gravel Do You Need Under Pavers?
Quick answer: A 12 x 10 ft paver patio (120 ft²) with a 4 in gravel base and 1 in of bedding sand needs 1.63 yd³ of base gravel and 0.41 yd³ of sand with 10% waste. The calculator rounds bulk orders up to 0.5 yd³ steps, so order 2 yd³ of gravel and 0.5 yd³ of sand. The 4 in and 1 in come from a paver maker's installation guide: follow your paver maker and your local conditions.
Pavers sit on two layers you do not see when the job is done: a compacted gravel base and a thin screeded bed of sand. Both are ordered by volume, and the volume comes from the patio area and the depth of each layer. The numbers below come from the pavers calculator. The guide on how many pavers a patio needs covers the pavers themselves.
- Pavers (4 x 8 in)568 pavers
- Base gravel, bulk (4 in compacted)2 yd³
- Bedding sand, bulk (1 in)0.5 yd³
- Edge restraint44 ft
Where the depths come from
The calculator's starting depths are 4 in for the compacted base and 1 in for the bedding sand. Both come from one paver maker's installation guide: the base figure is the low end of the range it gives for foot traffic and light vehicles, and the sand figure is the bedding depth it recommends. Other makers' guides can differ, and heavier traffic, cold climates and soft soil can call for a deeper base. Your pavers, your soil, your frost conditions and local code decide the real depths, so use the numbers here to see how much material a depth means, and take the depths themselves from your paver maker.
The calculator allows other depths because the right ones change from site to site. If you enter a base thinner than the 4 in default, it flags the result as thin. For patios 20 ft or longer on a side, it adds a reminder about slope for drainage and compacting in layers, and the reminder is a prompt to ask your supplier, not a design.
The formula, step by step
Both layers use the same arithmetic as any gravel or sand bed. Here it is for the 12 x 10 ft patio.
- Area. 12 ft × 10 ft = 120 ft².
- Gravel volume. 120 × 4 in ÷ 12 = 40 ft³. Divide by 27 for cubic yards and add 10% waste: 40 ÷ 27 × 1.1 = 1.63 yd³.
- Sand volume. 120 × 1 in ÷ 12 = 10 ft³. Divide by 27 and add 10% waste: 10 ÷ 27 × 1.1 = 0.41 yd³.
- Round to the order. The calculator rounds bulk orders up to 0.5 yd³ steps, an assumption (suppliers set their own): gravel 2 yd³, sand 0.5 yd³.
- Weight, if your supplier sells by the ton. 1.63 yd³ × 1.4 tons per yd³ is about 2.3 tons. That weight figure is the calculator's assumption for loose crushed gravel. Ask your supplier for theirs.
The calculator applies the same 10% allowance to the sand and the gravel that it applies to pavers. Loose material settles under the compactor and spills at the edges, so some allowance is sensible. You can change it.
Gravel and sand by patio size
The table runs seven patio sizes with the 4 in base and 1 in of sand. "Exact" is the volume with 10% waste, and "order" is that volume rounded up to the 0.5 yd³ step.
| Patio size | Area | Gravel (yd³) | Gravel to order (yd³) | Sand (yd³) | Sand to order (yd³) |
|---|---|---|---|---|---|
| 6 x 6 ft | 36 ft² | 0.49 | 0.5 | 0.12 | 0.5 |
| 8 x 8 ft | 64 ft² | 0.87 | 1 | 0.22 | 0.5 |
| 10 x 10 ft | 100 ft² | 1.36 | 1.5 | 0.34 | 0.5 |
| 12 x 10 ft | 120 ft² | 1.63 | 2 | 0.41 | 0.5 |
| 12 x 16 ft | 192 ft² | 2.61 | 3 | 0.65 | 1 |
| 16 x 20 ft | 320 ft² | 4.35 | 4.5 | 1.09 | 1.5 |
| 20 x 20 ft | 400 ft² | 5.43 | 5.5 | 1.36 | 1.5 |
Notice how the sand line behaves on small patios. The 36 ft² patio needs only 0.12 yd³ of sand, but the bulk order still rounds up to 0.5 yd³. Sand is a thin layer, so its volume is 0.25 of the gravel's here, and the ordering step wastes more of it. That is the case where bags may fit better, as the next section shows.
Bulk or bags
For a small patio, bags of sand and gravel may be easier than a delivery, since a bulk load comes as a pile you must move. The gravel and mulch calculator turns the same area and depth into bags. The table uses a bag yield of 0.5 ft³, which is the calculator's label-typical value: your bag says its own.
| Patio size | Sand, bulk (yd³) | Sand, bags | Gravel, bulk (yd³) | Gravel, bags |
|---|---|---|---|---|
| 6 x 6 ft | 0.5 | 7 | 0.5 | 27 |
| 8 x 8 ft | 0.5 | 12 | 1 | 47 |
| 12 x 10 ft | 0.5 | 22 | 2 | 88 |
| 16 x 20 ft | 1.5 | 59 | 4.5 | 235 |
The calculator treats about 1 yd³ as the point where bulk delivery usually becomes more practical for gravel and mulch. The example patio takes 22 bags of sand and 88 bags of gravel, which is a lot to carry, and the table shows how fast the bag counts climb. Ask your supplier about delivery terms and minimum loads. This site does not list prices.
What if the base is deeper?
A deeper base is a change you may need. Soft soil, cold climates and heavier use are among the reasons a paver maker's guide may call for more than the default. The table shows what each depth does to the 12 x 10 ft example. The depths are what-ifs for comparison, not recommendations.
| Base depth | Gravel (yd³) | Gravel to order (yd³) | Weight (tons) |
|---|---|---|---|
| 4 in | 1.63 | 2 | 2.3 |
| 6 in | 2.44 | 2.5 | 3.4 |
| 8 in | 3.26 | 3.5 | 4.6 |
| 12 in | 4.89 | 5 | 6.8 |
Going from 4 in to 6 in takes the order from 2 to 2.5 yd³. Check your paver maker's instructions for the base that suits your pavers and your use before you order.
What if the sand layer changes?
The sand layer is the thin one, and the calculator only accepts a narrow range of sand depths. Treat the difference as a what-if: your paver maker states one depth for the bed, and the calculator's default of 1 in follows the guide it cites.
| Sand depth | Sand (yd³) | Sand to order (yd³) |
|---|---|---|
| 0.5 in | 0.2 | 0.5 |
| 1 in | 0.41 | 0.5 |
| 1.5 in | 0.61 | 1 |
| 2 in | 0.81 | 1 |
Because the order rounds up in 0.5 yd³ steps, several of these depths land on the same order. For a small patio the leftover sand in the pile can be bigger than the layer itself.
Total depth to dig
The excavation has to hold the base, the sand and the paver itself. For the defaults, the base and sand add up to 4 + 1 = 5 in before you count the thickness of your pavers. Paver thickness is not in the calculator because it does not change how many pavers or how much gravel you need, but it does set how deep the hole goes, so read it on the label. Also plan where the dug-out soil goes, and slope the surface as your maker's instructions say.
How waste changes the order
The calculator applies the same 10% waste setting to the pavers, the gravel and the sand. It is a rule of thumb, not a measured compaction figure. Here is what other allowances do to the example patio.
| Waste | Gravel (yd³) | Gravel to order (yd³) | Sand (yd³) | Sand to order (yd³) |
|---|---|---|---|---|
| 0% | 1.48 | 1.5 | 0.37 | 0.5 |
| 10% | 1.63 | 2 | 0.41 | 0.5 |
| 15% | 1.7 | 2 | 0.43 | 0.5 |
| 20% | 1.78 | 2 | 0.44 | 0.5 |
The guide on waste factors explains how to pick one, and the guide on gravel under a concrete slab shows the same volume math applied to a slab base.
Common mistakes with a paver base
- Forgetting the base and sand are separate orders. The pavers, the gravel and the sand each come as their own line.
- Using the sand depth for the gravel or the reverse. The two depths are separate inputs.
- Treating the example depths as a rule. They follow one maker's guide: follow yours and your local conditions.
- Skipping waste. Compaction makes the loose volume shrink.
- Forgetting the ordering step. A small sand need still rounds up to 0.5 yd³ in bulk.
- Confusing yards and tons. Ask whether the supplier quotes by the yard or by the ton and convert with their weight.
- Measuring the patio instead of the excavation. If the base extends past the pavers to hold the edge, measure the base footprint.
Frequently asked questions
How much sand and gravel do I need under pavers?
For a 12 x 10 ft patio with a 4 in base and 1 in of sand, 1.63 yd³ of gravel and 0.41 yd³ of sand with 10% waste. In bulk, order 2 yd³ of gravel and 0.5 yd³ of sand.
How deep should the gravel base be under pavers?
The calculator's default of 4 in follows one paver maker's installation guide. The right depth depends on your pavers, soil, climate and use, so follow your paver maker and local conditions.
How much sand goes under pavers?
The calculator's default is 1 in of bedding sand, again from a paver maker's guide. For the example patio that is 0.41 yd³ with waste, 0.5 yd³ as a bulk order.
How many tons of gravel is that?
About 2.3 tons for the example, using the calculator's 1.4 tons per cubic yard for loose crushed gravel. Real weight varies, so ask your supplier.
Do I need both gravel and sand?
The calculator lists both because the common paver installation described by the maker it cites uses a base and a bedding layer. Your paver maker's instructions say what your pavers need.
Can I buy sand and gravel in bags?
Yes, for small patios. The 12 x 10 ft example takes 22 bags of sand and 88 bags of gravel at 0.5 ft³ per bag. As the table shows, the bag counts climb fast on larger patios.
Should I order extra?
The calculator already adds 10%. Raise it if the ground is uneven or you are unsure how much compaction you will do.

Sources and assumptions
These are the settings behind every number above. Verified figures link to a source. Editable defaults are common rules of thumb: change them in the calculator to match your product and your site.
| Setting | Value | Status | Source |
|---|---|---|---|
| paver base depth | 4 in | Verified 2026-11-15 | Western Interlock paving stone installation guide: 4 to 6 in of compacted base for light vehicular and pedestrian traffic (6 to 12 in for heavy traffic). 4 in is the… |
| paver bedding sand depth | 1 in | Verified 2026-11-15 | Western Interlock paving stone installation guide: a uniform depth of 1 in of coarse concrete sand is recommended for the bedding layer. |
| paver waste | 10 percent | Editable default | Rule of thumb, editable: extra pavers for cuts at edges and breakage. Not verified. |
| bulk order increment | 0.5 yd3 | Editable default | Assumed ordering step for bulk gravel, mulch, soil and sand; yards differ. Rule of thumb, not verified. |
Keep reading
- How Many Pavers Do You Need for a Patio?A 12 x 10 ft patio of 4 x 8 in pavers needs 568 pavers with 10% waste (516 before). Tables by patio and…
- How Much Gravel Do You Need for a Patio Base?A 10x10 patio with a 4 inch gravel base needs 1.23 cubic yards, about 74 bags. See the formula, a depth…
- How Many Pavers Do You Need for an 8x8 Patio?An 8x8 ft patio needs 303 pavers of 4 x 8 in with 10% extra, 1 yd³ of base gravel and 0.5 yd³ of sand. See…
- How Many Pavers Do You Need for a 10x10 Patio?A 10x10 ft patio needs 473 pavers of 4 x 8 in with 10% extra, 1.5 yd³ of base gravel and 0.5 yd³ of sand…
- How Many Pavers Do You Need for a 10x12 Patio?A 10x12 ft patio needs 568 pavers of 4 x 8 in with 10% extra, 2 yd³ of base gravel and 0.5 yd³ of sand. See…
- How Many Pavers Do You Need for a 12x12 Patio?A 12x12 ft patio needs 681 pavers of 4 x 8 in with 10% extra, 2 yd³ of base gravel and 0.5 yd³ of sand. See…
- How Many Pavers Do You Need for a 12x16 Patio?A 12x16 ft patio needs 908 pavers of 4 x 8 in with 10% extra, 3 yd³ of base gravel and 1 yd³ of sand. See…
- How Many Pavers Do You Need for a 14x14 Patio?A 14x14 ft patio needs 927 pavers of 4 x 8 in with 10% extra, 3 yd³ of base gravel and 1 yd³ of sand. See…